Dr Peter King

RF & Satellite Systems Consultant · Career & Background

Consultancy availability
I am completing my existing consultancy commitments and will then retire.
I am no longer accepting new clients.

info@rfconsult.uk · LinkedIn profile

My profile

I am a consultant RF and satellite systems engineer with a PhD (University of Surrey, 2007) and an MSc (University of Surrey, 2002) in Satellite and Mobile Communications, and a BSc (University of Essex, 1989) in Electronic Engineering (Telecommunications). Over the course of 35+ years, I have worked on 60+ projects across RF, microwave, mobile and satellite communications. My experience spans both systems-level engineering and hands-on RF design: from end-to-end modelling (DAC to ADC, antenna to ADC, DAC to antenna), link budgets and propagation, through to transceiver architecture, RF circuits, bring-up, testing and optimisation.

Examples from previous work include projects with organisations such as AST SpaceMobile, European Space Agency, AAC Clyde Space, Thales, Satellite Applications Catapult, Microsoft Research, Airspan, Nortel, Lucent, Roke, Intellian, Plextek, Samsung, Cambridge Consultants and the University of Surrey.

Areas of experience

  • RF systems engineering
    • End-to-end systems modelling (DAC → ADC)
    • Link budgets (HF to E/W band)
    • Levels plans (ADC/DAC ↔ antenna)
    • Interference, dynamic range and signal integrity
    • ADC/DAC levels plans and performance trade-offs
    • Channel modelling and emulator programming
    • Radio propagation measurement campaigns
    • Technical leadership / technical management
  • Radio transceiver design and applications
    • Satellite payloads, satcom terminals and gateways
    • Commercial airliners
    • Inter-satellite links
    • Array antennas
    • Microwave links
    • Mobile UE and base station work (2G-5G)
    • Channel sounders
    • Custom ASIC / RFIC / MMIC / module specification
  • RF circuit design and implementation
    • Discrete RF design (DC to ~20 GHz)
    • Receivers and transmitters
    • Phase-locked loops
    • Power amplifiers and linearisation
    • AGC and APC control loops
    • Simulation, schematics, layout, prototype
    • PCBA bring-up, test and optimisation
    • Cost reduction and factory yield improvement

Methods and tools

Fully equipt RF lab with VSA, SA, VSG, VNA, PM, NFM, PSUx4, soldering, inspection and kits of parts. Software used include Keysight ADS, MATLAB, SIMetrix SPICE and Microsoft 365, alongside custom RF analysis applications developed for client projects.

Case studies (last 10 years)

A client needed a mmWave feeder link between a network of ground stations and a constellation of satellites. I helped by designing the architecture of the ground station, owning the link budget, and designing the architecture of the satellite transceiver. Owning the complete link from DAC to ADC meant it could be optimised by balancing factors such as EIRP, G/T, EVM, NPR, bandwidth, radio propagation channel, regulatory emissions, cost, reliability, availability, redundancy, efficiency, ease of installation, test and maintenance. I defined the requirements for subsystems such as the transceiver card, LNA and HPA; some were procured and for modules developed in-house, I specified the architecture line-up at RFIC/ASIC block level. After the ground stations and satellites were built, I checked the test results against my simulations and analyses, and helped troubleshoot issues and advised on technical concessions where appropriate.

A client was building a large array antenna at UHF. I designed the front-end module architecture from ADC/DAC to antenna and defined the requirements of the array and the electronics for each element, specifying the precise requirements of ASICs, RFICs, mixers, PLLs, filters, LNAs, PAs and DSAs to meet the array EIRP, G/T and sidelobe performance needed.

A client was developing a radio system for commercial aircraft that used air-to-ground and air-to-satellite links for diversity. I designed the aircraft terminals and specified the requirements for each block in the line-up from antenna to ADC/DAC. I also wrote models for the radio channel that the aircraft experienced during flight and these were uploaded to a channel emulator. The emulator was used for lab testing the complete system prior to expensive flight trials.

A client had designed a payload and wanted an independent check prior to launch. I created simulations, models and analyses to show the client the predicted performance, and this resulted in a few refinements to the design.

A client wanted to add an inter-satellite link to their constellation. I produced simulations, models and analyses to show the geometry, link availability, C/N and Doppler during the orbit. I also designed the ISL beam-hopping RF array antenna and defined the line-up from ADC/DAC to antenna.

A client wanted a satcom terminal for a well-known satellite constellation. I designed the architecture from antenna to ADC/DAC to meet standards and regulatory requirements. I also designed the PCBA with RF circuit design, simulation, schematics, layout, bring-up, debug, test, all on time and within budget; work was carried out in my RF lab with weekly reporting via Microsoft Teams.

A client was developing a new satellite and hired me to model the TT&C, feeder and user link budgets and simulate the C/N, Doppler and data throughput during a satellite pass using adaptive modulation and coding techniques. I was also tasked with defining the payload radio systems and liaising with suppliers.

Client feedback

  • "Peter has many strengths, including RF systems analysis and architectural design. Pete produced some excellent analyses making difficult things seem simple. I found Pete very approachable and easy to work with. He communicates extremely well and is flexible in his attitude." — Senior Director
  • "I worked with Pete when preparing RFI/RFQ responses for Radio Access Systems. He was always extremely responsive and his input was of an exceptionally high quality under tight timescales. I trusted Pete to interface directly with our strategic OEM partners and customers and this resulted in winning some key accounts." — SVP
  • "Pete is a very talented RF Engineer with expertise at all levels of the RF Design, theoretical and hands-on. He is a cool-minded Engineer and very easy to get on with." — Principal RF Engineer
  • "Pete is a very competent RF Designer. He was given a high level of design responsibility in his roles. Pete worked for the department several times and was usually the first contractor to be considered if a new role arose, especially if it was a complex task." — Project Manager
  • "On the RFU, I think we are where we are because of you and thanks a million for that, I can't praise you enough for what you're doing! Your great knowledge and understanding of RF and analogue electronics have allowed us to develop the RFU in record time, almost fully matching the requirements first time! This is a real achievement and something to be very proud of!" — Senior Director